Reese 44051 PROFESSIONAL RECEIVER User Manual download pdf

Installation Instructions

Toyota Tacoma

Part Numbers:

44051

33025

Equipment Required:

Wrenches: 9/16, 3/4, 18mm, 19mm, #45 Torx®

Drill Bits: None

Frame

1. Remove (2) two center Torx head bolts from bottom of bumper (3/8” bolts).

2. Remove (1) one nut from existing bumper bracket bolt at location shown above.

3. Set angle bracket in place over existing bumper bolt as shown.

4. Raise hitch up to frame and align rearmost holes in frame and bracket, install 1/2” hex head bolt with 1/2 “ toothed washer through angle

bracket, frame, and hitch bracket. Loosely apply 1/2” flanged locknut. This will hold receiver in place.

5. Install 3/8” hex bolt with 3/8” lock washer and 3/8” toothed washer, through strap on the end of the hitch box from bottom and into bumper

where torx head bolts were removed (See diagram on other side).

6. Install 1/2” hex head bolt with 1/2” toothed washer through angle bracket, frame and hitch in forward hole in frame. Install 1/2” flanged locknut

on the bolt.

7. Reinstall nuts on 12mm bumper bracket bolts.

8. It may be necessary to remove the rubber muffler hanger so that the nut above the exhaust can be torqued.

9. Tighten all fasteners.

Rev. A6-27-06N33025Sheet 1 of 1

z 2002, 2006 Cequent Towing Products

Flat Washer 3/8Qty. (2)

Hex Nut 1/2-13Qty. (4)

Lock Washer 3/8Qty. (2)

Conical Washer 1/2Qty. (8)

Bolt 3/8-16 X 1.50Qty. (2)

Bolt 1/2-13 X 1.75Qty. (4)

Tighten all 3/8” fasteners with torque wrench to 35 Lb.-Ft. (47 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: F33025

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

500 (227 Kg)5000 (2270 Kg)

Weight Carrying

Ball Mount

550 (250 Kg)5500 (2497 Kg)

Weight Distributing

Max Tongue

WT (LB)

Max Gross

Trailer WT (LB)

Hitch type

Wiring Access Location: PU1, PU2

Tighten all 1/2” fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)

Tighten all 12mm fasteners with torque wrench to 85 Lb.-Ft. (115 N*M)

Existing 12mm

bumper bracket bolt

(see Note 2)

Frame angle bracket

is inside frame on

both sides

Form: F205 Rev A 5-6-05

Installation Instructions 1

Summary of Contents

Page 1 - Installation Instructions

Installation InstructionsToyota TacomaPart Numbers:4405133025Equipment Required:Wrenches: 9/16, 3/4, 18mm, 19mm, #45 Torx®Drill Bits: None1Frame1. Rem

Comments to this Manuals

No comments

Reese 44051 PROFESSIONAL RECEIVER User Manual

Browse online or download User Manual for For the car Reese 44051 PROFESSIONAL RECEIVER. Reese 44051 PROFESSIONAL RECEIVER User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Reese 44051 PROFESSIONAL RECEIVER