Reese 44670 PROFESSIONAL RECEIVER User Manual download pdf

Installation Instructions

Toyota Highlander

Part Numbers:

75726

87615

44670

Hitch Shown In Proper Position

Equipment Required:

Wrenches: 10mm, 12 mm, 14mm,

17mm, small screwdriver, Phillips head

screwdriver, & 6” socket extension

Frame rail

Fastener Kit: 75726F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

5000 (2270 Kg) 750 (341 Kg)

Weight Carrying

Ball Mount

5000 (2270 Kg) 750 (341 Kg)

Wiring Access Location: SUV3, 4

Frame rail

Fascia

Vehicles

heating/cooling

hoses located in

this area.

Use caution not to

pinch.

Note: When stowing the spare

flat

tire,

necessary

lift

Existing weldnuts in

both vehicle frame

Exhaust bridge

Sheet 1 of 3 75726N 8-5-11 Rev. A

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Form: F205 Rev A 5

Tighten all M10 x 1.25 CL10.9 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M))

Qty. (9) Hex Bolt – M10 x 1.25 x 30mm CL10.9

Qty. (9) Conical Toothed Washer – 3/8”

1. If present, remove plastic appearance panels which cover driver’s and/or passenger’s side frame rails. Remove the plastic

rivets that fasten the fascia tabs to the appearance panel. Note: Remove the center of the rivet with a small screwdriver.

Passenger’s side panel can be reinstalled. Return drivers’ side panel and fasteners to owner.

2. Remove tow hooks from each frame rail and return hooks and fasteners to vehicle owner.

3. Remove plastic and rubber plugs from bottom of frame rail, and outside frame rails. Return to owner.

4. Raise hitch over exhaust tip as shown. Be careful not to pinch hoses on the outside of the passenger side frame rail or scratch

fascia. Lower the exhaust if additional clearance is need. Remove excess caulking from rails if needed.

5. Align hitch into position over existing weldnuts as shown and install fasteners to bottom of frame rails. Do not tighten. Note: the

hitch will contact a fascia tab on the passenger side at the exhaust bridge.

6. Install remaining fasteners into the weldnuts on the outside of the frame rail. Be careful not to pinch hoses.

7. Torque all fasteners to specifications.

8. Reinstall the vehicle exhaust. (If required)

9. Reinstall passenger side appearance panel.

flat

tire,

necessary

lift

up on the rear edge of the tire

to clear hitch.

1 2 3

Summary of Contents

Page 1 - 87615

Installation InstructionsToyota HighlanderPart Numbers:75726 87615 44670Hitch Shown In Proper PositionEquipment Required:Wrenches: 10m

Page 2

Instructions d’installationToyota HighlanderNuméros de pièce :75726 87615 44670Attelage montré dans la position appropriéeÉquipement r

Page 3

Instrucciones de instalaciónToyota HighlanderNúmeros de partes:75726 87615 44670El enganche se muestra en la posición correctaEquipo n

Comments to this Manuals

No comments

Reese 44670 PROFESSIONAL RECEIVER User Manual

Browse online or download User Manual for For the car Reese 44670 PROFESSIONAL RECEIVER. Reese 44670 PROFESSIONAL RECEIVER User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Reese 44670 PROFESSIONAL RECEIVER