Reese 44636 PROFESSIONAL RECEIVER User Manual download pdf

Installation Instructions

Ford Flex

Ford Flex EcoBoost

Lincoln MKT

Part Numbers:

75679

87571

44636

78189 U-Haul

Fascia

Hitch Shown In Proper Position

Equipment Required: Lubricant or Soapy water

Fastener Kit: 75679F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Wiring Access Location: SUV1, SUV2

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

4000 (1816 Kg.) 400 (182 Kg.)

Weight Carrying

Ball Mount

4000 (1816 Kg.) 400 (182 Kg.)

Wrenches: 18mm, 19mm, 6” Ratchet

Extension ( Ford Flex)

Exhaust hanger bracket

Vehicle Frame

Rubber Exhaust Hanger

Existing

Weldnuts

Spray some lubricant on the

rubber exhaust hangers and then

use a screwdriver or pry bar to

Note: On the Lincoln MKT and Ford Flex EcoBoost model have duel exhaust, repeat instruction listed below to the passenger side

exhaust.

1. Lower exhaust by removing two (2) bolts which attach exhaust hanger bracket to driver’s side frame rail. Return to owner.

Note: Re

attachment of exhaust hanger bracket may be made easier by removing rubber exhaust hanger from hanger bracket

Qty. (4) Hex Bolt M12 x 1.75 x 40mm CL8.8

Qty. (4) Conical Toothed Washers ½”

Fasteners Typical Both Sides of Vehicle

use

screwdriver

pry

bar

remove all of the rubber hangers.

Support the system while you

remove all of the hangers

Note:

attachment

exhaust

hanger

bracket

may

made

easier

removing

rubber

exhaust

hanger

from

hanger

bracket

2. Detach the rubber isolator from the front exhaust hanger located forward of muffler, just behind rear axle. Be careful not to allow

muffler to fall under their own weight. Spraying a lubricant on the metal hanger rod and the rubber isolator helps removal.

3. Rotate the hitch into position over the exhaust and align the slots to the existing weld nuts. Reattach exhaust hanger bracket to

underside of hitch bracket (as shown). On models with dual exhaust, do this on both sides of vehicle. Install fasteners as shown

above.

4. Tighten all fasteners to the required torque specification.

5. Raise exhaust back into position and reattach to rubber isolators. Spraying a lubricant or soapy water on the metal hanger rod

and the rubber isolator helps.

z 2009, 2010 Cequent Performance Products

Sheet 1 of 3 75679N 4-7-10 Rev. B

Tighten all M12 x 1.75 CL8.8 fasteners with torque wrench to 68 Lb.-Ft. (92 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent

entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a

vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and

SAE J684.

Form: F205 Rev A 5

1 2 3

Summary of Contents

Page 1 - Installation Instructions

Installation InstructionsFord Flex Ford Flex EcoBoost Lincoln MKTPart Numbers:75679

Page 2 - Instructions d’installation

Instructions d’installationNuméros de pièces:CarénageFord Flex Ford Flex EcoBoost Lin

Page 3 - Instrucciones de instalación

Instrucciones de instalación Números de partes:Placa protectoraFord Flex Ford Flex EcoBoost

Comments to this Manuals

No comments

Reese 44636 PROFESSIONAL RECEIVER User Manual

Browse online or download User Manual for For the car Reese 44636 PROFESSIONAL RECEIVER. Reese 44636 PROFESSIONAL RECEIVER User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Reese 44636 PROFESSIONAL RECEIVER