Reese 44704 PROFESSIONAL RECEIVER User Manual download pdf

Installation Instructions

Mercedes-Benz ML350*

(will not fit 2012 & newer ML350 DEISEL.)

Part Numbers:

44704

75874

87653

Hitch Shown In Proper Position

Equipment Required:

Wrenches: 10mm, 3/4

Drill Bits: NONE

1. Support the exhaust and remove exhaust from hangers so exhaust can be lowered out of the way.

2. Remove the plastic fascia brackets (return to owner) shown in Figure 1. and the exhaust heat shield cover hardware, so shield can move freely

above the exhaust.

3. Remove the four (2 per side) lower M10 nuts from the bumper brackets (do not discard).

4. Raise the hitch into position with side brackets installed on the bumper bracket bolts and loosely reinstall the M10 nuts removed in step 4.

5. Raise the forward end of the hitch to the cross member under the car. Place bolt plate with 1/2” bolts and washers installed through existing

vehicle cross member holes and into matching hitch bracket.

6. Tighten from 10mm bolts to torque specs below and reinstall the heat shield. (note heat shield may need to bend a little to be reinstalled

around hitch.)

7. Using Zip ties provided. Zip tie hitch to the fascia where the removed brackets where located.

Tighten all M10 fasteners with torque wrench to 38 Lb.-Ft. (52 N-M)

Sheet 1 of 3 75874N 10-17-13 Rev. A



Qty. (2) 1/2 -13 x 4.00 Bolt



Qty. (5) Zip Ties



Qty. (2) 1/2-13 Hex Nut



Qty. (2) 1/2 Conical Washer

Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (101 N-M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: 75874F

Do Not Exceed Lower of Towing Vehicle Manufacturer’s Rating or

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

4000 (1 816 Kg) 525 (238 Kg)

Weight Carrying

Ball Mount

3500 (1 589 Kg) 525 (238 Kg)

Wiring Access Location: SUV3, SUV4

Bumper Bracket

Figure 1.

Remove in

step 2.

*Will not fit models equipped with Air

Suspension Package

Existing Nuts

3 2

Sub Frame

Fascia

Printed in Mexico

1 2 3

Summary of Contents

Page 1 - Installation Instructions

Installation Instructions Mercedes-Benz ML350* (will not fit 2012 & newer ML350 D

Page 2 - Instructions d’installation

Instructions d’installation Mercedes-Benz ML350* (ne convient pas aux modèles ML350 DIESEL 2012 et plus récents.) Numéros de pièce : 44704 75874 8765

Page 3 - Instrucciones de instalación

Instrucciones de instalación Mercedes-Benz ML350* (no apto para modelo ML350 DEISEL 2

Comments to this Manuals

No comments

Reese 44704 PROFESSIONAL RECEIVER User Manual

Browse online or download User Manual for For the car Reese 44704 PROFESSIONAL RECEIVER. Reese 44704 PROFESSIONAL RECEIVER User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Reese 44704 PROFESSIONAL RECEIVER